Acura TSX TL High Power 6 Channel PNP Amplifier

Description

If you are looking to make your Acura TSX or Acura TL loud but don’t want to break your head with all the wiring our plug and play amplifier may be the solution. This amplifier requires new power and ground lines. You can find ground underneath the seat or on mounting bracket nearby. For power you will have to run the four gauge power wire up your battery. This amp isn’t recommend for first time DIY installers.

This amplifier can be used with the factory radio or an aftermarket radio. This amplifier can be used with the factory speakers in your Acura or new aftermarket speakers. We recommend upgrading your speakers when installing this amplifier. This amplifier is best used to power all of your speakers as full range speakers but can be configured to power a subwoofer and center channel like the factory amplifier. If you have any current sound issues this amplifier may or may not fix them please call us at 877-542-2872 so we can verify the cause of your audio issues and if this amplifier will fix them.

When installing this amplifier you will not need to run any new speaker wires to each speaker. Instead you will run the provided wire harness to the correct locations. This will include an audio input and audio output harness. Both harnesses will run to the same location but will plug into their respective connectors only. The primary power wire will be have to be ran to the battery and the ground wire will be secured to a location nearby. The remote wire for the amplifier will be combined with the audio input section of the amplifier. The amplifier will also come with a mounting bracket and mounting hardware for metal and carpet. If you are installing the amplifier below a seat use the carpet hardware if you are installing the amplifier against metal use the metal hardware.

In your 2004 to 2008 Acura TSX this amplifier installs below the passenger seat and you run your wire up the center console to the factory amplifier locations.

In your 2004 to 2008 Acura TL this amplifier installs below the passenger seat and you run the wire below the passenger side trim to the passenger kick panel where the factory amplifier is.

In your 2009 to 2014 Acura TSX without factory navigation this amplifier installs in place of the factory amplifier in the trunk on the passenger side behind the trunk liner.

In your 2009 to 2014 Acura TL without factory navigation this amplifier installs in place of the factory amplifier in the trunk on the passenger side behind the trunk liner.

In your 2007 to 2013 Acura MDX without factory navigation this amplifier installs below the passenger seat and the wire runs underneath the passenger trim to the factory amplifier connections behind the glovebox.

In your 2009 to 2014 Acura TSX and Acura TL with factory navigation this amplifier integrates into the factory amplifier in the trunk on the passenger side behind the trunk liner. You will mount this amplifier along side the factory amplifier.

This amplifier is rated for 140W x 4 @ 2ohms + 185 x 2 @ 2ohms. So you want to pair JBL or Audison speakers for the best performance. At 4 ohms the amplifier is rated for 85w x 6. This amplifier is extremely efficient so while it gets loud it will not put a strain on your factory electrical system only drawing 54 amps at max musical performance.

The amplifier comes tuned based on your conversation with our technicians. Please make sure to use a good contact number for your order so that our team may reach out and tune your amplifier correctly for your radio and speaker combination. If you are looking for all the technical details of this amplifier please check out this link.

FAQs

1. Can I use this amplifier with the factory speakers?
   – yes but this amplifier is powerful enough to easily blow the factory speakers so be-careful.
2. Can I use this amplifier if I have an aftermarket radio installed?
   – yes you can use this amplifier with the factory radio or aftermarket radio
3. Can I use this amplifier with aftermarket speakers?
   -yes you can use this amplifier with 4ohm, 2ohm or 8 ohm speakers.
4. How is it plug and play if I have to run wires?
   – The amplifier is labeled plug and play because you don’t have to figure out any of the wiring. You just have to run wires to the correct locations. All the wires are terminated and labeled so it takes the guess work out of the installation.
5. Why doesn’t it work for newer Acuras?
   – The amplifier may work on newer Acuras and vehicles with navigation but it has not been tested and we don’t have first hand experience with that exact vehicle. When we do we will update the description of the amplifier.
6. How much louder is this amp than factory?
   – Your factory amplifier has an output of roughly 20-30Watts per channel. This amplifier outputs 125 watts per channel at two ohms. That means this amp is possibly up to 4-6 times more powerful than the factory amplifier and nearly three time as loud.
7. Who makes this amplifier?
   – This amplifier is made by Audison they are a high end audio company. This amplifier is the SR6.600 and comes with a two year warranty.
8. Why would I buy it from you when I could just buy it direct?
   – If you are an advanced DIYer then you can easily buy this amplifier direct and configure all the settings. You will also need to do all the wiring which can be a bit time consuming. If you aren’t an advanced DIYer all the settings on the amplifier and the wiring can get overwhelming and confusing. Our amplifier comes pre-tuned and wired so you can just plug everything in and start enjoying.